A Van Nuys electrical build-out often starts with one big question: can the existing system handle what the new tenant plans to run? Van Nuys has a wide mix of commercial property, from industrial buildings near the Van Nuys Airport to shops along Van Nuys Boulevard and offices near the Civic Center. Many of these buildings are decades old. Past tenants with very different needs set the size of their panels, circuits, and service. This guide explains how to evaluate panels, circuits, and equipment loads before a build-out begins.
Tenants, landlords, and project managers will find practical steps here for planning the electrical side of a project.

Why Evaluation Comes First
Electrical surprises are expensive. A panel that is too small, wiring that is unsafe, or a service that cannot grow can stall a project for months. In contrast, a careful review at the start shows what work lies ahead. It also helps you budget, plan the schedule, and negotiate with the landlord. So evaluation is the smartest first step in any Van Nuys electrical build-out.
Start the Van Nuys Electrical Build-Out With an Equipment List
Before anyone opens a panel, list everything the tenant will use. Include lights, outlets, HVAC, water heaters, compressors, machines, ovens, servers, and chargers. For each item, note the voltage, phase, and amps or watts. This list becomes the basis for all the load math. Without it, the review is only a guess.
Evaluating the Service
The service is the power coming into the building from the utility. It has a size in amps and a voltage, such as 120/208 or 277/480. Small shops may have 200 amps or less. Industrial buildings may have much larger services. So the electrician checks the main switch, meter, and utility equipment. If the tenant’s load tops the service size, the building needs an upgrade.
Van Nuys Electrical Build-Out Panel Review
Next, the electrician opens each panel. They look at the rating, the number of spaces, and the breakers in use. They also check for heat damage, rust, and loose parts. Electricians also flag a few older brands that tend to fail and need to go. In addition, panel labels are often wrong in older buildings. Tracing circuits helps clear up the confusion.
Van Nuys Electrical Build-Out: Circuit Review
Circuits carry power from the panel to lights, outlets, and equipment. The electrician checks wire size, insulation, and connections. Old cloth-covered wire, aluminum branch wiring, or ungrounded outlets are warning signs. In addition, overloaded circuits often show up as warm outlets or tripping breakers. Any of these may mean rewiring parts of the space.

Calculating Equipment Loads
With the equipment list and the panel review in hand, the electrician works out the total load. The math follows the National Electrical Code from the NFPA. For example, a cooler that cycles counts differently from a light that stays on all day. In the end, the number shows whether the current system can keep up.
Single-Phase vs. Three-Phase in Van Nuys
Many industrial tenants in Van Nuys use machines that need three-phase power. Most large buildings near the airport have it. However, smaller retail and office spaces may have only single-phase power. Adding it later is costly and slow. So confirm it before signing a lease for a shop that runs heavy machines.
Van Nuys Electrical Build-Out for Industrial Users
Industrial tenants have special needs. Compressors, welders, CNC machines, and conveyor systems all draw heavy current. In addition, many need dedicated circuits and disconnect switches near the equipment. Busway systems overhead can make it easier to move machines later. So plan the layout of machines with the electrician from the start.
Van Nuys Electrical Build-Out Lighting for Large Spaces
Warehouses and shops need bright, even light. Older high-bay lamps burn lots of energy and need minutes to reach full brightness. LED high-bay fixtures give better light and cut power use. State energy code also asks for sensors that turn lights off in empty aisles. The California Energy Commission lists these rules. Lighting upgrades often free up panel capacity too.

EV Chargers and Fleet Vehicles
Many Van Nuys businesses run vans and trucks. More of them now switch to electric vehicles. Each charger can pull a large load through a whole shift. So if the tenant plans chargers now or later, include them in the load calculation. In addition, plan a conduit path to the parking area during the build-out. Running empty conduit now costs far less than trenching later.
Working With LADWP
If the service must grow, the city-owned utility, LADWP, has to approve and schedule the work. They may need to add a transformer or change the meter. These steps can take weeks or months. So contact LADWP as soon as the load calculation shows an upgrade is needed. Our page on electrical service upgrades explains the process.
Permits and Inspections
Van Nuys is a Los Angeles community, so LADBS reviews and inspects the work. Any panel change, new circuit, or service upgrade calls for a permit. The plans must show load calculations, panel schedules, and a one-line diagram. After the work, inspectors check everything before power is restored.
Safety During the Evaluation
Opening a live panel is dangerous. Only qualified electricians with proper protective gear should do it. In addition, arc flash labels on larger equipment show the risk level. So never let untrained staff poke around in electrical rooms. Safety comes first in every step of the review.
Old Additions and Hidden Wiring
Older Van Nuys buildings have often been changed many times. Past owners added offices, mezzanines, and sheds, sometimes without permits. As a result, wiring may run in odd places or connect to the wrong panel. So the electrician should trace key circuits and note anything that looks unsafe. Fixing hidden problems early prevents failed inspections later.
Turning the Review Into a Plan
After the evaluation, the electrician writes up what they found. The report lists what can stay, what must be repaired, and what must be replaced. In addition, it estimates costs and time for each item. With this report, the tenant and landlord can make smart decisions about the Van Nuys electrical build-out. Our page on build-out electrical services describes common scopes.
Budgeting the Van Nuys Electrical Build-Out
The final number depends on square footage, the tenant’s machines, and how much of the old system can stay. A small office may need little more than new lights and outlets. A machine shop in an old building may need a new service and panels. So get a detailed estimate before committing. Early numbers are easier with our square-foot cost guide.
Plain Tips for Tenants
- Write down every machine and its power needs
- Ask if the building has three-phase power
- Have panels checked before you sign
- Swap old lights for LEDs to free up capacity
- Contact LADWP as soon as an upgrade looks likely
Van Nuys Electrical Build-Out Checklist
- Build a complete equipment list
- Check the service size and voltage
- Inspect every panel and its breakers
- Review circuits and wiring condition
- Run a full load calculation
- Confirm three-phase needs
- Plan LADWP and LADBS steps early
Build on a Solid Foundation
A careful evaluation of panels, circuits, and loads sets up the whole build-out for success. With clear data in hand, you can plan, budget, and schedule with confidence. Visit our Los Angeles electrical page to learn more, or contact our team for an evaluation.

